DBXi-15D DBXi - high performance subwoofers with advanced technology. DBXi is a showcase in the use and adaptation of extremely advanced technology. DBXi simplifies the choice for the serious bass enthusiast. It is no longer necessary to decide whether the subwoofer should be an SPL or SQL design. DBXi provides high SPL while remaining fast, accurate and musical. Innovative technology and a revolutionary machining process are key elements of the DBXi design. Enabling us to produce a subwoofer capable of thunderous deep bass with speed, precision and articulation. Development of the DBXi The development of the new DBXi drivers began with an in-depth review of all elements in subwoofer design. The conclusion was that a refinement of existing technology could not overcome known limitations. New technology was a necessity for delivering bone-crushing low frequency response while still retaining the speed and composure required for higher cutoff frequencies. Many manufacturers are able to make heavy and slow woofers that begin to stumble over themselves at 60 - 70 Hz. Also, many manufacturers are able to produce overdeveloped mid-tone drivers that are fast, but not able to go deeper than 60 Hz. One of the major design requirements for DBXi was a linear frequency response from 20 to 250 Hz (15 "DBXi). What distinguishes great subwoofer units from mediocre, is paradoxically their ability to reproduce the higher frequencies. Especially for music reproduction - a quick and hard-hitting bass is much more immersive than a bass that feels heavy and slow. A woofer must be taut, responsive and hard hitting. Magnetic system with nuclear technology DBXi's ultra powerful magnet system is the result of an unusual collaboration with the nuclear power industry in Wisconsin. In order to achieve the desired power density without the cost of rare earth magnets, it was necessary to increase the strength of conventional magnets significantly. This initiated the partnership with a manufacturer of plutonium fuel rods (radioactive fuel cylinders for nuclear power plant) in Wisconsin. This manufacturer had invented a special hot forging process, which enabled the production of a magnet motor backplate and center section out of a single piece of metal. Using the fuel rod hot forging technology we were able to produce super high gauss motors using traditional ferrite based magnetic material. The ultra-high magnetic intensity is obtained because all the magnetic field lines can now transmit magnetic flux without loss, since the magnet structure is now one piece instead of the more traditional multi piece design. It provides an extremely efficient and accurate motor. High-performance voice coil At the heart of DBXi sits an oversized voice coil. All aspects of the voice coil design have been optimized for maximum performance, durability and sound quality. The voice coil former (the cylinder to which the coil is wound) is made of aluminum, not cellulose (cardboard), Kapton ® or fiberglass. The use of aluminum prevents hot-spots on the voice coil - due to the superb heat conductivity inherent to aluminum. In essence the entire voice coil becomes one big heat sink. The voice coil is wound of copper wire and meets mil-std specifications for temperature resilience. German made high temperature adhesives are used to fuse the coil to the former. This guarantees peak performance even during hard and continuous operation. TCT - Turbine Cooled Transducer SWE- Super Wide Edge suspension DBXi features the extreme SWE (Super Wide Edge) edge suspension geometry. The massive height of 31mm speaks to the excursion potential. The suspension is of the single-roll type - laminated and thermally pressed for extreme strength and mobility. It allows cone travel of more than 62 mm. This ensures perfect reproduction of even the most bass heavy soundtracks The Super Wide Edge suspension allows record breaking excursion without deformation or increased mechanical resistance. Parabolic deep dish woofer cone The DBXi cone is made of a proprietary non-pressed fiber reinforced cellulose pulp substance with extreme stiffness. The cone is then superimposed with a parabolic deep dish made of a strong space age polymer that obtains additional rigidity by its geometric shape. The cone does not flex or deform regardless of input power and frequency. Super spider with dual symmetric stitched tinsel leads The DBXi spider is of the super spider type, which means the spider has the same diameter as the cone -this ensures the spider is not limiting excursion. For optimal performance the edge suspension and spider must have the same excursion potential, this is not possible with a traditional spider of limited diameter. The tinsel leads to the voice coil are sewn into the spider to ensure against collision with the cone during extreme excursion. This also extends the life of the tinsel leads, as they now bend more gently over a longer distance. The symmetrical design of the tinsel leads prevents an asymmetrical pull on the cone. The result is longer woofer life, and greater endurance. XLT chassis geometry The DBXi is based on Earthquakes signature XLT chassis geometry. It is the optimal design for extreme excursion. The XLT chassis allows for extra length between the spider (center suspension) and the magnetic gap. And it is designed to accommodate oversized spiders and voice coils. DBXi- High Performance - High quality - Advanced technology Priced and sold per piece. Specifications:
Dimensions: TS Parameters: TS Data Obtained using the VI-BOX high power system. Specs Measured @ 100watt rms. Standard TS is done @ 1-3 watts which is insufficient for obtaining data in a high excursion modern woofer
|
|
|